|
Roman Wetrooms Tanking Kit
RSH01 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm.
RSH12 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm. 4 Internal corners, 2 external corners, 2 pipe sleeves.
|
|
|
|
|
Choose kit
|
|
|
|
|
Roman Wetrooms Shower Floor
To make the installation of a wetroom even simpler, Roman offers a pre-formed shower floor which is designed to be installed onto your beams and then tanked and tiled over. This creates a natural fall to the waste – eliminating the need for the installer to create the drainage slope with adhesive. The pre-formed shower floor then offers the reassurance of a tray, but a true wetroom look is still achieved.
Specification
Designed with 22mm thick edge work to be compatible with WBP Board.
It can be trimmed by 50mm around the edges to miss joists if necessary.
Self-supporting - installation directly to joists with no additional support
Non porous
Off-Centre waste to avoid joists
17mm of fall to waste
Available in 2 sizes: 1000mm x 1000mm & 1350mm x 850mm
Suitable for installation to: timber floors, floating floors and concrete floors
|
|
Price:
£265.00
|
|
|
Choose floor
|
| |
|
|
|
|
|
Roman Wetrooms Complete Kits
RSHWP01 RSH01 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm.Shower floor 1000 x 1000mm. Tile waste
RSHWP02 RSH01 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm.Shower floor 11380 x 850mm. Tile waste
RSHWP03 RSH12 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm. 4 Internal corners, 2 external corners, 2 pipe sleeves. Shower floor 1000 x 1000mm. Tile waste
RSHWP04 RSH12 The kit includes 2 ltr of primer. 15m of Roman shield tape. 1 self adhesive drain mat. 9kg of Roman tanking compound. Set of instructions. Covers 10sqm. 4 Internal corners, 2 external corners, 2 pipe sleeves. Shower floor 1350 x 850mm. Tile waste
|
|
|
|
|
Choose kit
|
|
|
|
|
Roman Wetrooms Preparation
Constructing the Wetroom
There are several different ways of constructing a wetroom, there are however some basic principles that must be observed, these are: The floor may be screeded, constructed from heavy duty wooden sheets such as plywood or created using a pre-made shower tray former. In all cases there must be a gradual slope to fall towards an appropriate shower outlet, the structure must be solid, without flexing and any joints in the construction material must be firm and well fitting.
The body of the shower outlet must be recessed or cast into the floor in such a way that the top of the flange is on a level or fractionally lower than the floor surrounding it. There can be no upwards step into the shower outlet. Roman Shield can not be used directly over conventional narrow wooden floorboards, such boards must be replaced or covered with a sheet material such as plywood.
Ensure all surfaces in the construction areas are dry and level as well as free from grease dust and other seperating layers.
|
|
|
|
|
|
|
Roman Wetrooms Applying the Primer
The entire floor area of the room should be primed with a turn up of 100mm onto the walls. The walls should be also be primed floor to ceiling in the showering area and in the splash zone of the shower., normally 100mm past the showering area. I.E. If your showering area is 100 x 100cm prime floor to 110 x 110cm. The primer can be applied using a small fur roller, brush or air gun. The curing time is a minimum of 2 hours.
|
|
|
|
|
|
|
Roman Wetrooms Apply Outlet Sleeve
Apply the self adhesive outlet sleeve ensuring it is flat with no raised edges, creases or bubbles. The centre of the outlet sleeve is then removed and the waste traps clamping ring is fixed into position.
|
|
|
|
|
|
|
Roman Wetrooms Apply the Shield Tape, Sleeves and Corners
the Roman sheild tape, sleevs and corners are bedded down using Roman tanking compund. All wall to wall and wall to floor junctions as well as butt joints and nail or screw heads musr be reinforced with the tanking tape. The compound is applied using a medium size paint brush.
|
|
|
|
|
|
|
Roman Wetrooms Pre-checks.
Ensure the shield tape, pipe sleeves, corners and outlet sleeves have been fitted to the appropriate areas and wait until the tanking compound is dry. (curing time is 2-4 hours)
|
|
|
|
|
|
|
Roman Wetrooms Apply the Tanking Compound
The entire floor area of the room should be tanked with a turn up of 100mm onto the walls. The walls should be tanked floor to ceiling in the showering area and in the splash zone. the recommended finished thickness of the tanking compound is a minimum of 1mm, this is usually achieved in 2-3 coats. The tanking compound can be applied using a fur roller or a large paint brush. The curing time is 2-4 hours per coat.
|
|
|
|
|
|
|
Job Completed
You are now ready to start tiling as normal.
|
|
|
|
|
